Getting a good measurement for your snowmobile ski is essential for finding out if you have ridden or driven a particular model of snowmobile. If you want to keep the value of your vehicle, then it is best to avoid getting too many accessories attached to it. This is because most of the time these add-ons are expensive to replace. The best way to find out about the quality of any given piece of equipment is by getting a good measurement from someone with experience. This article will go over some useful tips on measuring your snowmobile as accurately as possible so you can get an idea of how it performs.
Table of Contents
Use A Stance Bag
When getting your measurements, it is important to make sure that you have all the necessary tools and equipment to do the job. One thing you should have with you is a sturdy bag or case to carry all the items in. Inside the bag or case, you should have all the following items:
- A pair of locking pliers
- A spirit level
- A level
- A hand-held drill
- A ratchet and extensions
- A tape measure
- A protractor
- A triangle
- A tape measurer
- A speed-ring magnet
- A spirit level vial
- An odometer
- A pencil
- Tape
- A socket set
- A ruler
- A protractor
- A dial indicator
- A ruler extension
- A tape measurer extension
Use The Right Ratchet Extension
Your ratchet tool should have a 6-inch extension so you can use it to tighten nuts and bolts accurately. Make sure you have the standard ratchet tool, which almost all home workshops have in their equipment. If you don’t have one, then you should pick one up at a hardware store. It is also advisable to use a socket set in place of a needle-nose pliers.
Measure It At The Top
When getting your measurements for the car, make sure that you stand at the top of the vehicle with the engine at the same level as the hood. This will ensure that the tires are not touching the ground and potentially causing damage. When taking the measurement, you should use the front of the engine as a reference point to find the back of the vehicle. Doing this will help you get an accurate idea of how much space you have behind you. You should also stand to the side of the vehicle when taking the measurement to ensure that the tire is not obstructing you from measuring accurately.
Use A Flat, Level Surface
To get an accurate measurement, you need to have a flat surface on which to stand. This will help eliminate any variation that could be caused by uneven or sloped surfaces. If you drive on any kind of terrain, then it is almost certain that some parts of the surface will be sloped or uneven. This will potentially ruin your accurate measurement reading if you do not have a level surface to stand on. Some experts recommend using a tile or a granite surface for your measurements because these are both very flat and stable. These surfaces are also easy to clean if you do not want to leave any marks behind when making your measurements.
Stand In The Right Place
Another thing you need to do is to make sure that you stand in the right place when taking your measurements. You should stand at the front of the vehicle with the wheels in the same direction as you are facing. This will ensure that the vehicle is parked in such a way that when you roll it forward, it will not tilt or turn over. You should also make sure that the ground is even and has no bumps or uneven spots on it. You can use a spirit level to make sure that there are no serious differences in level between the ground and the hood of the car. If you are in an auto accident or collision then this will be an important factor to determine how much damage was done to your vehicle.
Remove All The Attachments
When getting your measurements, you should also remove all the attachments from the vehicle. This will help eliminate the fact that the vehicle is not operating correctly and could potentially be dangerous. You should take this precaution when cleaning your vehicle before taking the measurement so you do not risk damage to any part of the vehicle. Before cleaning, you should check all the electrical connections and make sure that they are securely connected. You should also remove all the snow chains and other equipment that could be a safety risk if left alone (e.g. oscillating fans, etc.). Once you have removed all the attachments, it will be much easier to get an accurate reading.
Wrap Up All The Tubing
When getting your measurements, you should also take care of all the tubing that runs from one place to another. This includes hoses, wires, and plumbing. You should make sure that all these items are securely taped or bunged up near the area where they exit the vehicle. Taping these items will prevent them from being damaged when removing the car for measurement purposes. Bunging the items will restrict their movement and prevent any kinks or twists that could potentially cause breakage.
Take Your Time
Last but not least, you should take your time when measuring your vehicle. You should not rush the process because then you will almost certainly make a mistake and have to start over. Take your time to ensure that you get the measurement right the first time. You should also take the time to document all the measurements taken so you have them written down for future reference. This way, you will know exactly what your car is worth and can work out a price with the seller if needed. It is also advisable to take a digital picture of the car before beginning any repairs so you can reference the image should the need arise.
As you can see, there are many things you need to check before getting your measurements for a snowmobile. All these items will make a difference in the overall quality and accuracy of your measurement. It is important to keep in mind that no matter what, you must have a pair of locking pliers to adjust the oil cap if needed. Also, make sure that you have the correct tools for the job. All these things will make a difference in the end result of your measurement so take the time to do them correctly. Good luck out there.